Showing results: 991 - 1005 of 1021 items found.
-
PE-S330 -
Pasternack Enterprises, Inc.
PE-S330 part number from Pasternack is a PE-S330 twinax cable that is flexible. Pasternack PE-S330 flexible twinax cable is 100 Ohm and has a PE dielectric. Our PE-S330 twinax is constructed with a 0.33 jacket made of PVC. PE-S330 twinax has a shield count of 2 and the maximum frequency for this Pasternack cable is 400 MHz.
-
M-140HC -
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy!:Measurale Load Current at high voltage CV/CVT cables with grounding lines for shield phase.*Epoch-Making!:Can measure phase current of CVT cable just by putting CT head on to the conductors as well as CV cable just by clamping CT to the conductors in a lump.*Low Cost!:Can measure line/leakage current in the same manner as ordinary clamp meters.
-
RG180B/U -
Pasternack Enterprises, Inc.
RG180B/U part number from Pasternack is a RG180 coax cable that is flexible. Pasternack RG180 flexible coax cable is 95 Ohm and has a PTFE dielectric. Our RG180 coax is constructed with a 0.141 jacket made of FEP. RG180 coax has a shield count of 1 and the maximum frequency for this Pasternack cable is 3 GHz. RG180 coax cable has a maximum power of 250 watts at 1 GHz.
-
MT-7051N -
Prokit's Industries Co., Ltd.
Tests RJ45 TIA568A/B (AT&T 258A), 10 Base-T, Token ring, RJ-11/ RJ-12 USOC and Coaxial BNC cable.Automatically check cable for continuity, short, open and crossed wire pairs.Coaxial cable port indentifies cable conditions including shorts, shield opens and center conductor breaks.Main unit and remote allow one person testing.Power source: DC 9V BatteryDimension: 102x106x28 (mm)Cable not include
-
CS Analyst™ -
EMI Software llc
With CS Analyst circuits can be analyzed prior to fabrication to determine whether conducted susceptibility requirements will be satisfied. CS Analyst is ideally suited for predicting the effectiveness of EMI filtering for power line and signal line filters and for determining the effects of cable shielding and shield terminations.
-
RS Analyst™ -
EMI Software llc
With RS Analyst circuits can be analyzed prior to fabrication to determine whether radiated susceptibility requirements will be satisfied. RS Analyst is ideally suited for predicting the effectiveness of EMI filtering for power line and signal line filters and for determining the effects of cable shielding and shield terminations.
-
RG108A/U -
Pasternack Enterprises, Inc.
RG108A/U part number from Pasternack is a RG108 twinax cable that is flexible. Pasternack RG108 flexible twinax cable is 78 Ohm and has a PE dielectric. Our RG108 twinax is constructed with a 0.235 jacket made of PVC. RG108 twinax has a shield count of 1 and the maximum frequency for this Pasternack cable is 1 GHz. RG108 twinax cable has an attenuation at 1 GHz of 34.6 dB and a maximum power of 30 watts at 1 GHz.
-
RG62A/U -
Pasternack Enterprises, Inc.
RG62A/U part number from Pasternack is a RG62 coax cable that is flexible. Pasternack RG62 flexible coax cable is 93 Ohm and has a PE (AS) dielectric. Our RG62 coax is constructed with a 0.239 jacket made of PVC. RG62 coax has a shield count of 1, a RF shielding of 45 dB and the maximum frequency for this Pasternack cable is 1 GHz. RG62 coax cable has an attenuation at 1 GHz of 8.7 dB and a maximum power of 77 watts at 1 GHz.
-
PH-320/300 -
Pansco, Ltd
The plug‵N′check is our easiest-to use cable tester yet. Simply plug in both ends of a cable, and the easy-to-read LED display explains the cable type and checks whether cable is faulty or good automatically. A shield LED shows results of the shielding check and battery low indicator saves you from misreading the tester in case of low power. Will make work shorter and easier for the layman and the professional alike. Especially suited for installation and maintenance of residential networks.
-
AVS150 -
MadgeTech, Inc
Autoclave Validation System: Includes (1) HiTemp150 data logger with NIST Calibration Certificate, an extended range thermal shield, IFC200 interface cable, MadgeTechs Secure Software and IQ/OQ/PQ validation protocols, providing tools to users to assist with FDA 21 CFR Part 11 compliance.
-
410104732 -
Virginia Panel Corporation
This oversized backshell for the G6 ITA features an adjustable cable exit that can accommodate cable bundles up to 2.50". To accommodate cable exit size variations, excess shield material may be snapped off via a perforated design.This backshell also allows for an increased bend radius which is necessary for many wiring configurations including high speed due to larger wire sizes.Compatible with p/n's 310104318, 310104336, and 310104344 and the G6 ITA is backwards compatible with the G6X Receiver (310104481).
-
Langer EMV-Technik GmbH
The MP CI set up to measure coupling impedance is used to determine EMC characteristics of connectors and cables. The coupling inductivity defines the coupling inductance of external disturbance on the shield or on the ground with the desired signals. If the coupling inductivity is considered in the construction set-up and the pin or wire assignment of connectors or cables, then the connectors or cables will be more interference-resistant. The MP CI set-up for measuring coupling impedance can be used for following measurements at connectors or cables: 1. measurement of a single signal (common mode) 2. measurement of a symmetrical signal (common mode) 3. measurement of a symmetrical signal (differential mode)
-
PK-2030/2032/2033/2036/2037/2038 -
Pansco, Ltd
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
Morris Products Inc.
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
PH-100/120 -
Pansco, Ltd
The Lantracker is a network tester, pin-by-pin cable tester, and tone generator all in one. As a network tester, it detects whether a network is active or inactive and displays network speed (10/100/1000 Mbps) in either case. It also flashes the network hub or NIC’s port light corresponding to the cable it is connected to, to show the cable’s port number. As a cable tester, it performs loop-back or remote tests of network, data, voice, and coaxial cables, displaying the results on a pin-by-pin LED display which moves from pin to pin automatically or manually. The Lantracker can be used to test cable or shield integrity, testing network function and speed, and tracing cable using its tone generator function (tone probe not included). Includes an adaptor for testing coaxial-F cable. Uses 1 9V battery.
